逗游網:值得大家信賴的游戲下載站!

微信:doyo_game
關注逗游
單機首頁 游戲庫 排行榜 資訊 攻略 專題 合集 工具補丁 手機游戲 正版商城
所在位置:攻略中心 > 圖文攻略 > 微軟模擬飛行2020 > 正文

微軟模擬飛行2020空中客車A320Neo通用飛行教程

發布時間:2020-08-31 09:13 來源:bilibili  作者:冷庫黃

 

垂直模式和自動推力之間的相互作用

If you select a vertical mode like CLB or OP CLB by pushing or pulling the altitude knob the auto-thrust system will increase the engine thrust to climb thrust (THR CLB) and maintain that. The autopilot will then pitch up to keep the speed target. This means the autopilot is controlling the speed with the climb angle now and the engines are just producing the maximum climb thrust.

When you reach the target altitude the autopilot will capture the altitude (ALT*) and then maintain it (ALT). When this happens the auto-thrust switches back to SPEED mode and change the engine thrust to maintain the speed target again. Now the auto-thrust controls the speed again and the autopilot maintains the altitude.

A similar thing happens during the descent. If you have DES or OP DES engaged the auto thrust will retard the thrust to idle (THR IDLE) and the autopilot pitches down to keep the airspeed target. So again the autopilot is controlling the speed and the auto-thrust is just keeping a fixed thrust value, in this case idle. Once the aircraft has descended to the target altitude the auto-thrust controls the speed again and the autopilot switches to altitude hold.

Note - This works pretty well if you have the autopilot and auto-thrust engaged. If you control either of them manually you have to be careful because you as a pilot then need to make sure that the airspeed is kept within limits. Imaging the engines going to full throttle but you don't pull up to keep the airspeed. Or the engines go to idle and stay there but you don't pitch the nose down. This can get out of hand quickly. This is why most airlines require the pilots to either use both: AP and A/THR or neither. Or at least make sure that for landing the auto-thrust is indeed controlling speed and no longer keeping idle thrust.

如果通過推動或拉動高度旋鈕來選擇垂直模式(如CLB或OP CLB),則自動推力系統將增加發動機推力 至 爬升推力(THR CLB)并保持不變。然后,自動駕駛儀將加速以保持目標速度。這意味著自動駕駛儀現在通過爬升角來控制速度,而發動機僅產生最大的爬升推力。

當您達到目標高度時,自動駕駛儀將捕獲高度(ALT *),然后保持高度(ALT)。發生這種情況時,自動推力將切換回SPEED模式,并更改發動機推力以再次保持速度目標?,F(xiàn)在,自動推力再次控制速度,自動駕駛儀保持高度。

在下降期間也會發生類似的情況。如果您使用了DES或OP DES,則自動推力將使推力延遲至怠速狀態(THR IDLE),并且自動駕駛儀的俯仰角將降低以保持空速目標。因此,自動駕駛儀仍在控制速度,自動推力僅保持固定的推力值,在這種情況下為空轉。飛機下降到目標高度后,自動推力將再次控制速度,自動駕駛儀將切換到高度保持狀態。

注意 -如果您啟用了自動駕駛儀和自動推力,這將非常有效。如果您手動控制它們之一,則必須小心,因?yàn)樽鳛轱w行員,您需要確??账俦3衷谙拗品秶鷥?nèi)。想像一下發動機將要全開油門,但是您不會拉高以保持空速。否則,發動機會進入怠速狀態并停留在那里,但是您不會降低機鼻。這會很快失控。這就是為什么大多數航空公司要求飛行員同時使用:AP和A / THR或兩者都不使用的原因。或至少要確保降落時自動推力確實在控制速度,而不再保持空轉推力。

進入《微軟模擬飛行2020》專區
查看更多《微軟模擬飛行2020》攻略
標簽: 
http://4uh5.cn/article/403616復制本文地址
閱讀本文后,您的心情是:(選擇后可查看結果)
 
惡心
憤怒
強贊
感動
路過
無聊
雷囧
關注
今日關注游戲
游戲?qū)n}
IGN 9分以上作品 愿者上鉤釣魚的那點趣事 深冬之寒,來一起看看游戲中精美的雪景吧